kitchen Products Online

Tools and Process to Install Delta Kitchen Faucet

install Delta Kitchen Faucet

How to install a delta kitchen faucet? Installing a Delta kitchen faucet is easy and only takes a few minutes. The first thing you need to do is turn off the water to your sink. Next, use a Phillips head screwdriver to remove the handle. Use your screwdriver to remove these screws and then lift the faucet off of the sink.

Now, take a look at the new faucet and make sure that it will fit in the same hole as the old one. If not, you may need to use a drill to enlarge the hole. Finally, turn the water back on and test your new Delta kitchen faucet!

Tools & Materials Needed

  • Delta kitchen faucet
  • Basin wrench or adjustable wrench
  • Slip-joint pliers
  • Phillips screwdriver
  • Flathead screwdriver
  • Teflon tape
  • Pipe dope
  • Rags or paper towels

Optional

  • Adjustable wrench
  • Pipe cutter
  • Drain snake

Now that you have all of the tools and materials needed, let’s get started with the installation process!

Process of Installation

Installing a Delta kitchen faucet is a relatively easy process that anyone can do with a few basic tools. In this blog post, I’ll walk you through the steps necessary to install your new Delta kitchen faucet.

  1. Shut Off the Water Supply

Before you do anything else, you’ll need to shut off the water supply to your kitchen sink. This is important because you don’t want to accidentally flood your kitchen while you’re working on the faucet.

There are two ways to shut off the water supply: at the main shut-off valve for your home, or the shut-off valve under your kitchen sink. If you’re not sure which shut-off valve to use, just shut off both of them to be safe.

  1. Remove the Old Faucet

Once the water supply is shut off, it’s time to remove the old faucet. 

  • To do this, you’ll first need to remove the handles.
  • To remove the handles, start by unscrewing the screw that holds the handle in place. Once the screw is removed, you should be able to pull the handle off.
  • Next, use a basin wrench or adjustable wrench to remove the large nut that holds the faucet in place. With the nut removed, you should be able to pull the faucet out from the top.
  • If you have a sprayer attached to your old faucet, you’ll need to disconnect it before you can remove the faucet. To do this, start by unscrewing the retaining nut that holds the hose in place.
  • Once the retaining nut is removed, you should be able to pull the hose out of the faucet. With the hose removed, you should now be able to pull the faucet out from the top.

3. Install the New Faucet

With the old faucet removed, it’s time to install the new one. 

  • To do this, start by threading the supply lines through the holes in the bottom of the new faucet.
  • Next, apply a liberal amount of pipe dope or Teflon tape to the threads on the supply lines. This will help to create a watertight seal.
  • Now, thread the supply lines into the shut-off valves. Be sure to hand-tighten the valves until their snug.
  • Once the valves are tightened, you can now attach the faucet to the sink. Start by threading the large nut onto the faucet.
  • Once the nut is in place, use a basin wrench or adjustable wrench to tighten it. Be sure to hand-tighten the nut until it’s snug.
  • Now, it’s time to attach the handles. Start by threading the screws that hold the handles in place.
  • Once the screws are in place, use a Phillips screwdriver to tighten them. Be sure to hand-tighten the screws until their snug.
  • With the handles in place, you can now turn on the water supply and test your new faucet!

Read Alos: Install Double Kitchen Sink

Conclusion

Installing a delta kitchen faucet is a simple process that can be completed in a few minutes. With a few basic tools and a little bit of know-how, anyone can install a delta kitchen faucet. If you followed these steps, then you should now know how to install a delta kitchen faucet. Thanks for reading, and good luck with your project!

Leave a Comment